Yealink provisioning guide for VoIP 2.0

Modified on Thu, 5 Sep at 7:15 AM

Factory reset the device:

Yealink W dect series: (from the base station)

Power off the unit by unplugging the power cord from the back (for PoE, disconnect the network cable).
Wait for 15 seconds.
With the unit unplugged press and hold the connect button on the base station.
While still holding the connect button, plug the power (or network cable if PoE) back into the unit.
Wait until all three lights on the unit are showing as solid green, and release the connect button.
Wait approximately 5 minutes.
Reboot the unit by unplugging it from power for 15 seconds and plugging it back in.

Yealink T series :

Hold down the 'OK' button until the device prompts to reset to the factory settings.
Confirm prompt
Default pin/code: 0000 or 1379
Once the device has been reset to the factory settings you will need to log into the Web interface by entering the IP address into your web browser.

NB: The device and computer/laptop you’re using need to be connected to the same network.

How to locate the IP address:

Yealink W dect series:

Press the 'OK' button 3 times

Yealink T series:

Press the 'OK' button

NB: If the device has no IP this means the internet is not flowing through to the device. In this case check the ethernet cables, ethernet ports, firewalls, and broadband connection.

Once logged into the web interface follow these steps:

On the login screen, enter the username (default is 'admin') and the password (default is 'admin') and click Login.
Once logged in click the 'Settings' option in the top right corner.
Next, click on the 'Auto Provisioning' tab on the left. Then enter the provisioning string you copied from the MYbOnline portal into the 'Server URL' box.
Scroll down and click on 'Auto Provision.'

Yealink provisioning guide for VoIP 2.0

Factory reset the device:

Yealink W dect series: (from the base station)

Power off the unit by unplugging the power cord from the back (for PoE, disconnect the network cable).

Wait for 15 seconds.

With the unit unplugged press and hold the connect button on the base station.

While still holding the connect button, plug the power (or network cable if PoE) back into the unit.

Wait until all three lights on the unit are showing as solid green, and release the connect button.

Wait approximately 5 minutes.

Reboot the unit by unplugging it from power for 15 seconds and plugging it back in.

Yealink T series :

Hold down the 'OK' button until the device prompts to reset to the factory settings.

Confirm prompt

Default pin/code: 0000 or 1379

Once the device has been reset to the factory settings you will need to log into the Web interface by entering the IP address into your web browser.

NB: The device and computer/laptop you’re using need to be connected to the same network.

How to locate the IP address:

Yealink W dect series:

Press the 'OK' button 3 times

Yealink T series:

Press the 'OK' button

NB: If the device has no IP this means the internet is not flowing through to the device. In this case check the ethernet cables, ethernet ports, firewalls, and broadband connection.

Once logged into the web interface follow these steps:

On the login screen, enter the username (default is 'admin') and the password (default is 'admin') and click Login.

Once logged in click the 'Settings' option in the top right corner.

Next, click on the 'Auto Provisioning' tab on the left. Then enter the provisioning string you copied from the MYbOnline portal into the 'Server URL' box.

Scroll down and click on 'Auto Provision.'

This will cause the phone to reboot and do an upgrade. Once the upgrade is complete the device should be in working/registered status.

Need Help? If you need further assistance, please email our team at voipcare@bonline.com. We're here to help!